SpeedyBee F405 V4 BLS 60A 4in1 Stack

Product Description

The SpeedyBee F405 V4 BLS 60A 4in1 Stack with 60A BLS 4in1 ESC is SpeedyBee's value stack. It features a 60A 4in1 ESC and an F405 flight controller that supports the SpeedyBee phone app to configure your quad on the go. 🤩

The SpeedyBee F405 V4 features an upgraded 60A ESC with heat sink and various other upgrades :-

• Dual gyroscope power supply filtering

• Onboard 4 level battery indicators

• upto 8 motor support (FC)

• 5V + 9V BEC upgraded to 3A

• Built-in Barometer

■ 𝐒𝐩𝐞𝐞𝐝𝐲𝐁𝐞𝐞 𝐅𝟒𝟎𝟓 𝐕𝟒 𝐅𝐂 𝐒𝐩𝐞𝐜𝐢𝐟𝐢𝐜𝐚𝐭𝐢𝐨𝐧𝐬:

• MCU : STM32F405

• IMU(Gyro) : ICM42688P

• USB Port Type : Type-C

• Barometer : Built-in

• OSD Chip : AT7456E chip

• BLE Bluetooth : Supported.

• WIFI : Not supported

• Compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit

• ESC Signal : M1 - M4 on bottom side and M5-M8 on front side.

• UART : 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6

• ESC Telemetry : UART R5(UART5)

• I2C Supported.

• Traditional Betaflight LED Pad : Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.

• Buzzer : BZ+ and BZ- pad used for 5V Buzzer

• Power Input : 3S - 6S Lipo

• RSSI Input : Supported.

• Smart Port / F.Port : Not supported

• Firmware Target Name : SPEEDYBEEF405V4

• Mounting : 30.5 x 30.5mm( 4mm hole diameter)

• Dimension : 41.6(L) x 39.4(W) x 7.8(H)mm

• Weight : 10.5g

■ 𝐒𝐩𝐞𝐞𝐝𝐲𝐁𝐞𝐞 𝐁𝐋𝐒 𝟔𝟎𝐀 𝐄𝐒𝐂 𝐒𝐩𝐞𝐜𝐢𝐟𝐢𝐜𝐚𝐭𝐢𝐨𝐧𝐬:

• Firmware : BLHeli_S J-H-50

• Continuous Current : 60A * 4

• Burst Current : 80A(5seconds)

• TVS Protective diode : Yes

• External Capacitor : 1000uF Low ESR Capacitor(In the package)

• ESC Protocol : DSHOT300/600

• Power Input : 3-6S LiPo

• Power Output : VBAT

• Current Sensor : Support (Scale=386 Offset=0)

• ESC Telemetry : Not supported

• Mounting : 30.5 x 30.5mm( 4mm hole diameter)

• Dimension : 45.6(L) 8mm(H)

• Weight : ~23.5g

■ 𝐈𝐧𝐜𝐥𝐮𝐝𝐞𝐬:

• 1x F405 V4 FC

• 1x BLS 60A 4in1 ESC

• 1x 35V 1000uF Capacitor

• 5x M3 nylon nut

• 5x M3 silicone o-ring

• 1x M3.8 silicone grommet (for FC)

• 1x M3*8.1 silicone grommet (for ESC)

• 1x SH1.0 25mm-length 8pin cable (for FC-ESC connection)

• 5x M3x30mm iner-hexagon screw

• 1x DJI 6pin cable (80mm)

• 1x XT60 power cable (100mm)

𝘿𝙞𝙨𝙘𝙡𝙖𝙞𝙢𝙚𝙧:

𝘛𝘩𝘪𝘴 𝘱𝘳𝘰𝘥𝘶𝘤𝘵 𝘪𝘴 𝘴𝘰𝘭𝘥 𝘢𝘴 𝘢 𝘴𝘦𝘢𝘭𝘦𝘥 𝘪𝘵𝘦𝘮 𝘥𝘪𝘳𝘦𝘤𝘵𝘭𝘺 𝘪𝘮𝘱𝘰𝘳𝘵𝘦𝘥 𝘧𝘳𝘰𝘮 𝘊𝘩𝘪𝘯𝘢. 𝘈𝘴 𝘴𝘶𝘤𝘩, 𝘸𝘦 𝘥𝘰 𝘯𝘰𝘵 𝘱𝘳𝘰𝘷𝘪𝘥𝘦 𝘢𝘯𝘺 𝘸𝘢𝘳𝘳𝘢𝘯𝘵𝘺 𝘰𝘳 𝘨𝘶𝘢𝘳𝘢𝘯𝘵𝘦𝘦 𝘧𝘰𝘳 𝘵𝘩𝘦 𝘱𝘳𝘰𝘥𝘶𝘤𝘵. 𝘉𝘺 𝘱𝘶𝘳𝘤𝘩𝘢𝘴𝘪𝘯𝘨 𝘵𝘩𝘪𝘴 𝘱𝘳𝘰𝘥𝘶𝘤𝘵, 𝘺𝘰𝘶 𝘢𝘤𝘬𝘯𝘰𝘸𝘭𝘦𝘥𝘨𝘦 𝘢𝘯𝘥 𝘢𝘤𝘤𝘦𝘱𝘵 𝘵𝘩𝘢𝘵 𝘪𝘵 𝘪𝘴 𝘴𝘰𝘭𝘥 "𝘢𝘴 𝘪𝘴" 𝘢𝘯𝘥 𝘵𝘩𝘢𝘵 𝘵𝘩𝘦 𝘴𝘦𝘭𝘭𝘦𝘳 𝘪𝘴 𝘯𝘰𝘵 𝘭𝘪𝘢𝘣𝘭𝘦 𝘧𝘰𝘳 𝘢𝘯𝘺 𝘥𝘦𝘧𝘦𝘤𝘵𝘴, 𝘪𝘴𝘴𝘶𝘦𝘴, 𝘰𝘳 𝘮𝘢𝘭𝘧𝘶𝘯𝘤𝘵𝘪𝘰𝘯𝘴 𝘵𝘩𝘢𝘵 𝘮𝘢𝘺 𝘢𝘳𝘪𝘴𝘦. 𝘈𝘭𝘭 𝘴𝘢𝘭𝘦𝘴 𝘢𝘳𝘦 𝘧𝘪𝘯𝘢𝘭 𝘢𝘯𝘥 𝘯𝘰𝘯-𝘳𝘦𝘧𝘶𝘯𝘥𝘢𝘣𝘭𝘦.